Allied-telesis FORMULA 8200 Instrukcja Użytkownika Strona 1

FORMULA 8200 ™ Fast Ethernet Fiber Workgroup Switch Installation Guide PN 613-10688-00 Rev. A Fiber_Book Page 1 Tuesday, February 17, 1998 1:43 PM

Switch Installation6 Attaching a Console to the Switch You need the following equipment: ❑ A terminal or TTY-compatible terminal, or a portable compu

FORMULA 8200 Fiber Switch Installation Guide7 Figure 6: FORMULA 8200 POST Messages 4. Observe the LEDs for normal switch operation (Figure 7 and Ta

Switch Installation8 At initial startup, the switch operates at the default parameters listed in Table 2. If you want to change these settings, refer

FORMULA 8200 Fiber Switch Installation Guide9 Table 2: Default Fiber Switch’s Parameters Parameter Default Value System login adminSystem password

Switch Installation10 5. Log in at the prompt:— Log in as admin .— Enter the default password, switch .6. Enter SYSTEM/SHOW and verify the firmwa

FORMULA 8200 Fiber Switch Installation Guide11Connecting Devices to the Fiber PortsConnect the switch to any equipment that conforms to IEEE 802.3u st

Switch Installation12Sample Networking Applications10/100BASE-T NETWORK PORTS910111210/100BASE-T NETWORK PORTS13 14 15 16820110/100BASE-T NETWORK PORT

13Chapter 2TroubleshootingThis chapter provides information on isolating and resolving problems with FORMULA 8200 operation.Ethernet networks tend to

Troubleshooting14Checking LED StatusThe switch has system LEDs (Status and Power), located on the front panel, that indicate the switch’s overall oper

FORMULA 8200 Fiber Switch Installation Guide15IP AddressesThe FORMULA 8200 has a factory-assigned unique MAC address but does not have a default IP ad

Copyright  1998 Allied Telesyn International Corp.All rights reserved. No part of this publication may be reproduced without prior written permiss

Troubleshooting16CablingThe fiber media adapter for the 100Base-FX port uses only multimode 62.5/125 micron, 1300 nm fiber cable. The 100Base-FX media

17Appendix AProduct Specifications for the FORMULA 8200 SwitchNetwork Protocol Fast EthernetStandards Supported IEEE 802.1dIEEE 802.3u, 100Base-XData

Product Specifications for the FORMULA 8200 Switch18Electromagnetic ImmunityRF susceptibility EN61000, Level 4/3Electrostatic discharge (ESO)EN61000,

19Appendix BTechnical Support Fax OrderName___________________________________________________________________Company ________________________________

Fiber_Book Page 20 Tuesday, February 17, 1998 1:43 PM

21Appendix CFORMULA 8200 Fiber Switch Installation Guide FeedbackPlease tell us what additional information you would like to see discussed in the gui

Fiber_Book Page 22 Tuesday, February 17, 1998 1:43 PM

23Appendix DWhere To Find UsFor Technical Support or ServiceLocation Phone FaxAmericasUnited States, Canada, Mexico, Central America, South America1 (

Where To Find Us24AustraliaLindfield, NSWTel: (612) 416-0619, Fax: (612) 416-9764CanadaRexdale, OntarioTel: (416) 675-6738, Fax: (416) 675-0057Richmond

iii Table of Contents Chapter 1Switch Installation ...1Overvie

Fiber_Book Page iv Tuesday, February 17, 1998 1:43 PM

1 Chapter 1 Switch Installation This guide shows you how to install the FORMULA 8200 fiber switch from Allied Telesyn International Corp., shown in F

Switch Installation2 Overview The FORMULA 8200 includes the following hardware and software features: ❑ Eight or sixteen 100Base-FX, full duplex, dua

FORMULA 8200 Fiber Switch Installation Guide3 Verifying Your Switch Package Your FORMULA 8200 package consists of: ❑ One FORMULA 8200 fiber switch, e

Switch Installation4 Location Install the FORMULA 8200 on a sturdy, level surface in a ventilated area that is dust free and away from heat vents, wa

FORMULA 8200 Fiber Switch Installation Guide5 Installing the FORMULA 8200 in the Rack Caution When mounting the switch in a rack, do not stack units