Allied-telesis x600-48Ts/XP Instrukcja Użytkownika Pobierz pdf (Strona 60)

Chapter 3: Installing the Hardware

Resetting the Switch

You may need to reset the switch after upgrading the firmware or after you

have made a configuration change that requires resetting the switch to

activate the change.

To reset the x600 switch, perform the following procedure:

1. Locate the RESET button which is on the right hand side of the

faceplate.

2. Press the RESET button with the tip of a pen or a similar

nonconducting object as shown in Figure 26.

Figure 26. Resetting the Switch

1321

x600-24Ts/XP

Layer 3 Gigabit Ethernet Switch

9 11 13 15 17 19 21R 23R

10 12 14 16 18 20 22R 24R

FAU

RPS

MASTER

PWR

STATUS

SFP

L/A

BUSY

READY

FAU LT

RESET

CONSOLE

1 2 ... 55 56 57 58 59 60 61 62 63 64 65 ... 93 94

Installation Guide 1
Product Documentation 4
Starting a Management Session 5
Contacting Allied Telesis 8
Radiated Energy 9
Industry Canada 9
Translated Safety Statements 10
Contents 11
List of Figures 13
List of Tables 15
Overview 17
Introduction 18
Switch Descriptions 19
Connector 20
AC Power 20
RPS Connector 22
Distance 23
Auto-MDI/ 24
SFP Transceiver Slots 25
XFP Transceiver Slots 26
Redundant Twisted Pair Ports 27
SD Card Slot 28
Port LEDs 29
XFP Transceiver 30
Slot LEDs 30
System Status LEDs 31
Stack LEDs 32
Terminal Port 34
AT-LBM (Loop Back) Module 36
RPS INPUT 36
100-240VAC~ 36
VCS Stacking Module 37
AT-StackXG 37
STACK PORT 1 37
STACK PORT 2 37
AC Power Connector 38
Virtual Chassis Stacking 39
Introduction 40
uses two switches that are 41
Recovery States 42
Resiliency Link 44
Configurations 44
Resilient Stacked 45
Topology 45
Stack Formation 46
Selecting the Stack Master 46
Common Stack Configuration 47
Stack Management VLAN 47
Stack Member Identification 48
Management IP Addresses 49
Fallback Action 50
Re-elect New Stack Master 50
Recombining Separated Stacks 50
Adding a Stack Member 51
Replacing a Stack Member 51
Repairing a Broken Stub 51
Installing the Hardware 53
Reviewing Safety Precautions 54
Unpacking a Switch 56
100-240VAC 57
Resetting the Switch 60
Installing the 62
Cabling the Network Ports 65
Twisted Pair 66
Specifications 66
Transceiver 67
Installing an SFP 68
SFP Handle 69
4741 43 45 70
42 44 46 70
Installing an XFP 71
Powering on a Switch 74
Starting a Local 75
Management 75
Warranty Registration 76
Troubleshooting 77
Power LED is Off 78
SFP or XFP LED is Off 80
System Fault LED is Blinking 82
Chapter 5: Troubleshooting 84
Technical Specifications 87
Power Specifications 88
Certifications 88

Komentarze do niniejszej Instrukcji

Brak uwag

Allied-telesis x600-48Ts/XP Instrukcja Użytkownika Strona 60

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Sprzęt komputerowy Allied-telesis x600-48Ts/XP