Allied Telesis AT-8824 Przewodnik Instalacji Strona 114
- Strona / 202
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
1-36 show wanlb healthcheck Release Note
Software Version 2.7.5
C613-10454-00 REV A
show wanlb healthcheck
Syntax SHow WANLB HEALthcheck
Description This command displays information about wan load balancer healthcheck
resources (Figure 1-5, Table 1-4).
Figure 1-5: Example output from the show wanlb healthcheck command
Table 1-4: Parameters in the output of the show wanlb healthcheck command
Example To display all parameters of healthchecks use the command:
sh wanlb heal
Related Commands set wanlb healthcheck
WAN Load Balancer Healthcheck configuration
-----------------------------------------------------------
State ............................ ENABLED
Interval ......................... 60 seconds
Consecutive Success Checks ....... 2
Consecutive Failed Checks ........ 3
Number Host
-----------------------------------------------------------
1 172.20.156.100
2 www.vpn-site.com
3 www.critical-site.com
-----------------------------------------------------------
Parameter Description
State The state of the WAN load balancer healthchecks: one of enabled or
disabled.
Interval A fixed interval (in seconds) during which the WAN load balancer sends
a separate healthcheck message to each of its configured hosts.
Consecutive
Success Checks
The number of consecutive successful healthchecks to a specific host
before it is deemed to be reachable.
Consecutive Failed
Checks
The number of consecutive failed healthchecks to a host before that
host is deemed unreachable.
Number The number of the configured healthcheck host.
Host The healthcheck host's IP address or domain name.
- Software Version 2.7.5 1
- Overview of New Features 4
- MSS Clamping 5
- 8 MSS Clamping Release Note 8
- Software Version 2.7.5 9 9
- 10 MSS Clamping Release Note 10
- Syntax SHow PPP PPPoe 11
- Command changes 13
- Command Reference Updates 14
- Software Version 2.7.5 15 15
- Command Changes 18
- Syntax SHow IP 21
- DHCP Option 82 Relay 22
- Software Version 2.7.5 25 25
- Syntax SHow BOOTp RELAy 26
- IGMP Enhancements 28
- Filtering and Throttling 29
- Configuring IGMP 30
- IGMP Throttling 31
- Software Version 2.7.5 33 33
- Software Version 2.7.5 35 35
- OSPF Network Types 41
- [{FULl 45
- BGP Enhancements 46
- Automatic Summarising 48
- Aggregating Routes 50
- Software Version 2.7.5 53 53
- Syntax SHow BGP 55
- Syntax SHow BGP PEer[=ipadd] 56
- Software Version 2.7.5 59 59
- Software Version 2.7.5 61 61
- Firewall Enhancements 63
- UDP Port Timeout 65
- Software Version 2.7.5 67 67
- Software Version 2.7.5 73 73
- WAN Load Balancing 74
- VRRP Preemption Delay 75
- Software Version 2.7.5 77 77
- ..3600] [PRIOrity=1..254] 77
- Operating Principles 80
- Load Distribution Methods 81
- 1-4 Release Note 82
- WAN Load Balancing 1-5 83
- Healthcheck 84
- Assigning Weights 85
- Healthchecks 86
- Operation with Firewall 87
- 1-10 Release Note 88
- Before you 89
- Parameter Description 96
- ● eth (such as eth0, eth1) 100
- ● PPP (such as ppp0, ppp1) 100
- C613-10454-00 REV A 101
- Related Commands enable wanlb 109
- Syntax SHow WANLB 112
- Syntax SHow WANLB HEALthcheck 114
- ■ eth (such as eth0, eth1) 122
- ■ PPP (such as ppp0, ppp1) 122
- Filtering IP Routes 123
- 2-2 Release Note 124
- Introduction 125
- Types of Filters 126
- About AS Path Lists 127
- About Route Maps 127
- When to use 128
- About IP Route Filters 129
- Creating Filters 130
- Creating Route Maps for BGP 131
- How to create a route map 132
- ■ exclude the update message 133
- Example comparing 134
- AS path filter and 134
- Matching on 134
- Creating Route Maps for OSPF 138
- Creating IP Route Filters 141
- Applying Filters 142
- Applying AS path 143
- ■ prefix lists 148
- ■ AS path lists 148
- ■ route maps 148
- 2-28 Release Note 150
- [other-options] 150
- Filtering IP Routes 2-29 151
- The filtering 151
- Limitations of route 153
- Interface Routes 154
- Statically-Configured Routes 155
- Configuration Examples 156
- Using a Route Map 157
- Using an AS Path Filter 158
- Using Communities 160
- Command Reference 162
- Parameters for both 173
- Parameters for 173
- Parameters for set 176
- ■ an entire route map 181
- [PREfix=ipadd] 182
Powiązane produkty i podręczniki dla Switche sieciowe Allied Telesis AT-8824
(179 strony)
(32 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji