Allied-telesis AT-S94 CLI (AT-8000S Series) Instrukcja Użytkownika Pobierz pdf (Strona 29)

ACL Commands

Page 28

Parameters

•

disable-port — The Ethernet interface is disabled if the condition is matched.

• source — Source IP address of the packet.

• source-wildcard — Wildcard bits to be applied to the source IP address. Use 1s in the bit position to be

ignored.

• destination — Packet’s destination IP address.

• destination-wildcard — Wildcard bits to be applied to the destination IP address. Use 1s in the bit position to

be ignored.

• protocol —The name or number of an IP protocol. Available protocol names: icmp, igmp, ip, tcp, egp, igp,

udp, hmp, rdp, idpr, idrp, rsvp, gre, esp, ah, eigrp, ospf, ipip, pim, l2tp, isis.: (Range: 0 - 255)

• dscp number — Specifies the DSCP value.

• ip-precedence number — Specifies the IP precedence value.

• icmp-type — Specifies an ICMP message type for filtering ICMP packets. Enter a number, or one of the

following values: echo-reply, destination-unreachable, source-quench, redirect, alternate-host-

address, echo-request, router-advertisement, router-solicitation, time-exceeded, parameter-problem,

timestamp, timestamp-reply, information-request, information-reply, address-mask-request, address-

mask-reply, traceroute, datagram-conversion-error, mobile-host-redirect, mobile-registration-request,

mobile-registration-reply, domain-name-request, domain-name-reply, skip, photuriss. (Range: 0 - 255)

• icmp-code — Specifies an ICMP message code for filtering ICMP packets. (Range: 0 - 255)

• igmp-type — GMP packets can be filtered by IGMP message type. Enter a number, or one of the following

values: host-query, host-report, dvmrp, pim, cisco-trace, host-report-v2, host-leave-v2, host-report-v3.

(Range: 0 - 255)

• destination-port — Specifies the UDP/TCP destination port. (Range: 1 - 65535)

• source-port — Specifies the UDP/TCP source port. (Range: 1 - 65535)

• flags list-of-flags — List of TCP flags that should occur. If a flag is intended to be set, it is prefixed by ‘+’.If a

flag should be unset it is prefixed by ‘-’. Available options are: +urg, +ack, +psh, +rst, +syn, +fin, -urg, -ack,

-psh, -rst, -syn and -fin. The flags are concatenated to a single string. For example: +fin-ack.

IP Protocol Abbreviated Name Protocol Number

Internet Control Message Protocol icmp 1

Internet Group Management Protocol igmp 2

Transmission Control Protocol tcp 6

Exterior Gateway Protocol egp 8

Interior Gateway Protocol igp 9

User Datagram Protocol udp 17

Host Monitoring Protocol hmp 20

Reliable Data Protocol rdp 27

Inter-Domain Policy Routing Protocol

idpr 35

Ipv6 protocol ipv6 41

Routing Header for IPv6 ipv6-route 43

Fragment Header for IPv6 ipv6-frag 44

Inter-Domain Routing Protocol

idrp 45

Reservation Protocol rsvp 46

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 ... 401 402

Komentarze do niniejszej Instrukcji

Brak uwag

Allied-telesis AT-S94 CLI (AT-8000S Series) Instrukcja Użytkownika Strona 29

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Sprzęt komputerowy Allied-telesis AT-S94 CLI (AT-8000S Series)